Panasonic VB-44210G User Manual Download Page 336 | Manualshive

Page: 336 / 394

background image

Appendix B. CPC-AII/B 8.0 Feature Update

Section 700-Operation

Page B-10

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• The

*61

code toggles Variable Mode on and off. Press

ON/OFF *61

ON/OFF

again to turn Variable Mode off.

2.

While the extension is engaged in an intercom call, the 2nd line
will display select key 1 and 2 features from the Flexible
Function Screen assigned to display in FF3 ExtPort# 28#. The
same applies when the extension receives CO dial tone (FF3
ExtPort# 29#); during a trunk call (FF3 ExtPort# 30#); and
after dialing a busy extension (FF3 ExtPort# 33#).
• Use existing addresses FF1 2# 7# 1# thru 4# to assign select

key features to Flexible Function Screens.

• Select key features for

Fixed

Function Screens will not

appear on small-display phones.

3.

While the select key feature is displayed, you can execute the
feature by pressing the > or < select key.

Notes

Toggling Variable Mode On/Off with an FF-Key.

You can program the

*61

code into an FF-key: In programming mode, press FF5 (ExtPort)#

(KeyNo.)# (*61)#. The FF-key will toggle Variable Mode on/off while the
extension is idle or in an off-hook/dial-tone state. The FF-key LED will
remain lit (red) while Variable Mode is “On”. (You can also use a one-
touch key to toggle Variable Mode on and off; however, one-touch keys do
not contain an LED to indicate when Variable Mode is on.)

Variable Mode After Power-Cycling.

If Variable Mode is “On”, the

extension will stay in Variable Mode even after power-cycling (system is
powered down, then powered back up).

Incompatibility with older phone versions.

Variable Mode is available on

the 44-Series phones only.

Conditions under which Variable Mode does not work.

Variable Mode

will be temporarily overridden under the following conditions: during an
incoming message state, hold state, message-waiting state, or call-waiting
state. Incoming messages include:

CO Queuing
Incoming [trunk no.]
REV.[extension no.]
TRF.[trunk no.]
H-Recall
Call Wait
REC.[trunk no.]
Recall Hnt [Hunt Group no.]
DISA Incoming
Call [extension no.]
Transf [extension no.]
Recall [trunk no.]
HOLD Recall

«
...
334
335
336
337
338
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Pacific Sun Pages: 12

Brand: Jensen Pages: 13

Brand: Contec Pages: 15

Brand: audiophony Pages: 27

980590-0403 - Cordless Internet Handset USB VoIP Wireless Phone

Brand: Logitech Pages: 2

EASY CLEAR EQ-12-TH

Brand: Bunn Pages: 2

Brand: Furuno Pages: 2

Brand: auna multimedia Pages: 9

Brand: Tala Pages: 4

Brand: AEI Pages: 6

Brand: BRONDI Pages: 80

Brand: L-Acoustics Pages: 85

Brand: Motorola Pages: 37

Brand: Motorola Pages: 72

Brand: Motorola Pages: 2

Brand: Motorola Pages: 44

Brand: Motorola Pages: 21

Brand: Motorola Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands