Panasonic VB-44210G User Manual Download | Manualshive

Page: 195 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-79

Operation

To assign a voice mail key:

Note:

You cannot program this feature if trunks are assigned to the key. First

clear the trunk assignments, then use the following procedures to assign the
VM key.

1. Press

the

ON/OFF

key.

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

2. Press

the

PROG

key.

3. Press the FF key, DSS key, or One-Touch key.

4. Press

the

CONF

key.

5. Press

the

AUTO

key.

6. Dial the voice mail pilot number.

7. If the key is for personal message retrieval, enter a password (XXX or

AUTO followed by a speed dial number), if desired. If the key is for
attendant transfer to voice mail, do not enter a password, but include any
special codes (* or #, for example) if they are required by the voice mail
system.

Note:

If a password is used, it can be from 1 to 3 digits. If the password is

over 3 digits long, it must be assigned to a personal or system speed dial
number. If you are accessing the Panasonic Voice Mail, it is best to
include a # sign at the end of the password.

8. Press

the

HOLD

key.

To use a Voice Mail key:

When the VM key flashes, the user presses it to connect to the mailbox.

Related Programming

• FF5 (Keys): FF Key Assignment for Extensions

• FF5 (Keys): FF Key Assignments for DSS Consoles

«
...
193
194
195
196
197
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: W Audio Pages: 12

Brand: Radio Shack Pages: 28

ena Yealink SIP-T46S

Brand: Zayo Pages: 2

Brand: Uniden Pages: 41

Brand: Radio Shack Pages: 36

Brand: Selta Pages: 102

900 MHz Digital Spread Spectrum Cordless Phone with Dual Caller...

Brand: Radio Shack Pages: 28

Brand: Magnavox Pages: 24

VT-2481 Important s

Brand: VTech Pages: 46

the t.bone IEM-75

Brand: thomann Pages: 40

Brand: NAIM Pages: 51

Brand: Chamberlain Pages: 4

Brand: GE Pages: 100

Jitterbug Smart2

Brand: GreatCall Pages: 21

Brand: Ericsson Pages: 2

Brand: NEXT pool Pages: 19

Brand: Belson Pages: 34

Brand: DAPAudio Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands