Panasonic VB-44210G User Manual Download Page 51 | Manualshive

Page: 51 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-5

Extensions with the Verified Account Codes feature

disabled

can place

outside calls based on the TRS type assigned to the extension. If a user wishes
to place a call that would normally be restricted at the extension, the user can
enter a valid Verified Account Code to upgrade the TRS type assigned to the
extension.

Operation

1. Pick up the handset.

The phone issues intercom dial tone.

2. Dial

“#11.”

3. Enter the four-digit Account Code.

4. Press

“#.”

The phone issues intercom dial tone.

5. Press an available CO key or dial a trunk access code.

The phone issues outside dial tone.

6. Dial the telephone number.

The Verified Account Code TRS type remains in effect until the call is
completed.

Related Programming

• FF1 (System): Verified Forced Account Codes

• FF1 (System): Toll Restriction for Verified Forced Account Codes

• FF3 (Extension): Verified Forced Account Codes

• FF7 (TRS): Toll Restrictions

Hardware Requirements

• An SMDR printer or external call accounting system is required to collect

account code records.

Considerations

• Verified account codes are for outgoing calls only.

«
...
49
50
51
52
53
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: iDance Pages: 25

Brand: 5G HUB Pages: 16

Passport 500 Pro

Brand: Fender Pages: 4

Brand: Hanlong Pages: 26

Multi-room system

Brand: Systemline Pages: 22

Brand: VTech Pages: 31

Brand: Verizon Pages: 5

Brand: AT&T Pages: 4

Brand: Telefunken Pages: 41

Brand: AT&T Pages: 12

Brand: Daewoo Pages: 48

Brand: Grundig Pages: 16

Brand: Swisscom Pages: 14

The One MP-TO-01-C

Brand: Meet PAT Pages: 14

Brand: Amplicomms Pages: 23

2x10 PBX/KSU Telephone System

Brand: OnQ Technologies Pages: 3

Brand: FOUR Pages: 28

Brand: Kraken Acoustics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands