Panasonic VB-44210G User Manual Download Page 228 | Manualshive

Page: 228 / 394

background image

Chapter 5. DSLT Features

Section 700 - Operation

5-10

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

• FF3 (Extension): Permanent Call Forward Type (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Permanent Call Forward Extension (CPC-AII and CPC-

B Version 3.1 or higher)

• FF10 (Speed Dialing): System Speed Dial Numbers

• FF10 (Speed Dialing): Personal Speed Dial Numbers

Considerations

• Calls can be forwarded to extensions that have call forwarding activated.

For example, phone “A” can be forwarded to phone “B,” even if phone
“B” is forwarded to voice mail.

• With CPC-B 4.07 and later, extensions receiving forwarded trunk calls

display “CFWD NNN XXXXXX,” where “NNN” = the extension that
forwarded the call and “XXXXXX” = the trunk name or number.

• In CPC-A and CPC-B Versions prior to 5.0, DND and Absence Messages

cancel Call Forwarding.

Beginning with CPC-B Version 5.0, calls to an extension with DND or
Absence Message turned on are treated differently, depending on whether
they are trunk or intercom calls. Intercom calls receive busy tone; trunk
calls are routed to the extension defined in permanent call forwarding.

The following types of incoming trunk calls follow permanent call forward
settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

• Voice calls do not forward when Call Forwarding--No Answer is used.

• Extensions for which Call Forwarding-External has been set cannot:

- Be in the middle of an outside call when the feature is activated.

- Have a toll restriction setting that prohibits outside calls.

«
...
226
227
228
229
230
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Accutone Pages: 6

Brand: Ace Pages: 13

Brand: STARPLUS Pages: 294

Brand: Radio Shack Pages: 36

Brand: PNI Pages: 2

CIRFLEXX UMS 4100

Brand: Grundig Pages: 38

Brand: Jacob Jensen Pages: 16

Brand: Aastra Pages: 20

Brand: Uniden Pages: 46

Brand: Talkswitch Pages: 22

Brand: AT&T Pages: 4

POLYCOM SOUNDSTATION IP 6000

Brand: Armstrong Pages: 2

Brand: Yada Pages: 14

SPH200D - Cordless Phone / VoIP

Brand: NETGEAR Pages: 10

Brand: salmson Pages: 12

Brand: Johnson & Starley Pages: 2

Brand: Sound Ryder Pages: 20

Brand: Kenmore Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands