Panasonic VB-44210G User Manual Download Page 2 | Manualshive

Page: 2 / 394

background image

FCC Warning

Battery Recycling Statement

The information contained in this document is subject to change without notice and should not be
construed as a commitment by the Panasonic Telecommunication Systems Company (PTSC).
PTSC reserves the right, without notice, to make changes to equipment design as advances in
engineering and manufacturing methods warrant.

The software and hardware described in this document may be used or copied only in accordance
with the terms of the license pertaining to said software or hardware.

Reproduction, publication, or duplication of this manual, or any part thereof, in any manner,
mechanically, electronically, or photographically, is prohibited without permission of the
Panasonic Telecommunication Systems Company (PTSC).



Copyright 1995 by Panasonic Telecommunication Systems Company

Revised April 2000

All rights reserved.

Warning:

This service information is designed for experienced repair techni-

cians only and is not designed for use by the general public. It does not contain
warnings or cautions to advise non-technical individuals of potential dangers in
attempting to service a product. Products powered by electricity should be ser-
viced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this service information
by anyone else could result in serious injury or death.

This equipment generates, uses, and can radiate radio frequency energy, and, if not installed
and used in accordance with the instruction manual, may cause interference to radio commu-
nications. This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial environment. Operation
of this equipment in a residential area is likely to cause interference, in which case the user
at his own expense will be required to take necessary measures to correct the interference.

The following statement applies if you purchased backup batteries with your system.

The product you have purchased contains rechargeable batteries. The batteries are recycla-
ble. At the end of their useful life, under various state and local laws, it may be illegal to dis-
pose of these batteries into the municipal waste stream. Check with your local solid waste
officials for details on recycling options or proper disposal.

«
1
2
3
4
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: R.V.R. Elettronica Pages: 38

Brand: JBL Pages: 16

Authentics L 16

Brand: JBL Pages: 17

Brand: Nady Systems Pages: 11

Brand: Xblue Networks Pages: 52

kb sound Series

Brand: EIS Pages: 2

Brand: US Shift Pages: 44

VP59-Teams Edition

Brand: Yealink Pages: 8

Brand: Uniden Pages: 32

Brand: VocoPro Pages: 26

Brand: AmeriWater Pages: 67

SA10201 - Boom Box Audio System

Brand: Delphi Pages: 12

Brand: Sylvania Pages: 2

Brand: vitapur Pages: 36

Brand: OCL Pages: 2

Brand: Mitel Pages: 24

Brand: BT Pages: 51

Brand: QFX Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands