Panasonic VB-44210G User Manual Download Page 11 | Manualshive

Page: 11 / 394

background image

Section 700 - Operation

Introduction

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

x

About This Manual

Software Versions Covered by This Manual

This manual covers all versions of CPC-A, all versions of CPC-AII software
through Version 7.0 and CPC-B software through Version 7.0.

Differences in feature availability or operation are noted within each feature
description.

If you are using this manual for a single DBS system, make note of its
software version in the following table. This note may be referenced by
technicians or owners of the system.

Organization

This manual contains detailed descriptions of DBS features. The feature
descriptions are organized according to the following categories:

Software version information for systems shipped with this
document

CPC Model:

Software Version:

Feature Categories

Description

System Features

System Features are either available on a
system-wide basis or aid in the overall
administration of the DBS.

Attendant Features

Attendant Features assist the attendant in
serving as a central answering point. In addition,
attendant features also provide special
capabilities for monitoring and programming
extensions.

Key Telephone Fea-
tures

Key Telephone Features are available to DBS
key phones. DBS key phones are proprietary
digital sets that provide feature access through a
combination of feature keys and access codes.

Digital Single-Line
Telephone

(DSLT) Features

DSLT Features are available to Digital Single-
Line Telephones. DSLTs provide digital audio
quality and limited feature key access in a
single-line set.

Single Line Telephone
Features

SLT Features are available to industry-standard
2500 sets. Since SLTs are not equipped with
feature keys, most features are accessed by
using the dialpad and/or the switchhook.

«
...
9
10
11
12
13
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: NEC Pages: 7

Brand: NEC Pages: 2

Brand: NEC Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

KX-TG7622, KX-TG7623, KX-TG762

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 252

KX-TH112 - Cordless Phone - Operation

Brand: Panasonic Pages: 10

Brand: Jabra Pages: 16

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 372

JABRA FREEWAY HFS100

Brand: Jabra Pages: 40

Brand: Jabra Pages: 3

Brand: Solar Energy Pages: 4

Memory Phone 9825

Brand: Interquartz Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands