Panasonic VB-44210G User Manual Download

Page: 155 / 394

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-39

2. Dial the telephone number.

The dialed number appears on the display.

3. Complete the call and replace the handset.

• The line LED changes from green to red and then goes off.

• The time and date reappears on the display.

Related Programming

• FF1 (System): SMDR Display Start Timer for CO Calls

• FF5 (FF Keys): FF Key Assignments for Extensions

Considerations

• The duration of a call appears on the display while the call is in progress (if

enabled in programming).

• In CPC-A and CPC-B Versions prior to 3.1, the SMDR Display Start

Timer can be set to start 16 or 30 seconds after the last digit of the
telephone number is dialed.

In CPC-AII and CPC-B Version 3.01 or higher, the timer can be set to start
at 5, 16, or 30 seconds.

Conference Calls

(All Versions)

Description

Conference Calls allow an extension user to add a party to an existing
conversation.

Extension users can create the following types of Conference Calls:

• One outside line and two extensions

• Two outside lines and one extension

• One outside line and three extensions

• Two outside lines and two extensions

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands