Panasonic VB-44210G User Manual Download Page 357 | Manualshive

Page: 357 / 394

background image

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page F-1

Appendix F: CPC-EX 2.1 Updates

CPC-EX Version 2.1 adds support for the “Call Record” feature available with
PanaVOICE

™

Voice Mail systems. In addition, several quality improvements are

incorporated in Version 2.1.

CAUTION:

When using the “Call Record” feature in some states it is

illegal to record telephone communications without the consent of all
parties. In other states, it is illegal to record without the consent of one
party. These laws do not make the Call Record feature on a telephone
system illegal. Before activating this feature, please check applicable
state and federal laws.

Call Record

Requires PanaVOICE equipped with Software Version 2.1 (Q32136) or later.

Description

The call record feature allows a user to record a trunk conversation at the
press of preassigned

Call Record

FF key. The conversation is saved to the

user’s voice mail box.

Programming

See

Section 400 - Programming (Appendix H)

for more detailed

programming information.

Operation

To record a trunk call:

To record a trunk call, press the

Call Record

key. The LED flashes

while the connection to the Voice Mail recording port is being
established. This may take a few seconds. When recording begins, the
LED lights solid, “

Recording”

appears on the display, and the audio

message “Recording” is heard by both parties.

If call record cannot be established (no voice mail port available, no
conference circuit available, etc.), the LED extinguishes and a double
splash tone sounds.

Recording continues until you hang up, you press the

Call Record

key

again or PanaVOICE stops recording due to a PanaVOICE time-out,
lack of disk space, etc.

In the event PanaVOICE stops recording during a conversation, a beep
tone is issued, the LED extinguishes and “

Recording”

disappears from

the display.

If the outside party hangs up first, you may continue recording call
follow-up information.

«
...
355
356
357
358
359
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Talkswitch Pages: 30

Brand: Magnavox Pages: 23

Brand: Uniden Pages: 44

Brand: Paradyne Pages: 4

KX-T7400 Series

Brand: Panasonic Pages: 1

Brand: Doro Pages: 72

Brand: Kodak Pages: 25

Brand: Phonic Pages: 24

Brand: Uniden Pages: 36

Brand: CHARITY MOBILE Pages: 14

Brand: Crestron Pages: 26

Brand: Steren Pages: 26

Brand: Sunway Pages: 9

Brand: Uniden Pages: 8

Brand: JTS Pages: 2

Dual Series Housing CGS-12 10

Brand: Everpure Pages: 2

Brand: Curtis Pages: 12

Brand: Hitachi Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands