Panasonic VB-44210G User Manual Download | Manualshive

Page: 199 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-83

• If a ML or MCO key is assigned line group number 9 and LCR has been

activated, LCR is selected automatically.

• Press the ML or MCO key that flashes red to answer incoming calls.

• If one group is set aside for data lines, this feature can be used when a line

is needed for operations such as data transmission via modem.

Prime Line Preference

(All Versions)

Description

Prime Line Preference allows a user to place an outside call by simply
picking up the handset. When the user goes offhook, the trunk or trunk group
assigned to FF1 is automatically accessed. (Be sure to program one of the
other FF keys as an intercom key.)

Operation

1. Pick up the handset.

• The phone issues outside dial tone.

• The LED of the accessed line key lights green.

• “CO TALK #XX” (where “XX” is the line number) appears on the

display.

2. Dial the telephone number.

The number appears on the display.

Related Programming

• FF1 (System): Least Cost Routing (LCR) Access

• FF2 (Trunks): Pooled Trunk Access for Group “9”

• FF2 (Trunks): Pooled Trunk Access for Groups “81-86”

• FF3 (Extension): Forced Least Cost Routing

• FF5 (Keys): FF Key Assignment

• FF3 (Extension): Prime Line Pickup

«
...
197
198
199
200
201
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Univerge SV8100

Brand: NEC Pages: 5

Univerge SV8100

Brand: NEC Pages: 2

Univerge SV8100

Brand: NEC Pages: 184

Univerge SV8100

Brand: NEC Pages: 8

Univerge SV8100

Brand: NEC Pages: 15

Univerge SV8100

Brand: NEC Pages: 14

Brand: Yamaha Pages: 42

Brand: Uniden Pages: 32

OpenScape Desk Phone CP400T

Brand: Unify Pages: 130

OpenScape Desk Phone CP100

Brand: Unify Pages: 36

Brand: Uniden Pages: 6

Brand: Zip Pages: 16

Brand: JPS Pages: 116

Brand: ZETRON Pages: 60

Brand: auna multimedia Pages: 30

Brand: Aiwa Pages: 18

Medialon MAS Pro Dante D

Brand: 7th Sense Pages: 2

Brand: Uniden Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands