Panasonic VB-44210G User Manual Download Page 37

Page: 37 / 394

Section 700 - Operation

Chapter 2. Attendant Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

2-17

• The DSS key LED informs the attendant of the status of assigned

extensions. The LED lights red when the extension is busy and green when
Absence Message, Call Forwarding, or DND is activated.

• Pressing a DSS key while connected to an outside line places the line on

hold.

Headset Operation

(All Versions)

Description

A headset can be connected to attendant or non-attendant phones. (Dial tone
is normally turned off when the headset is connected.)

Operation

To use a headset:

1. Connect a headset to the telephone.

2. Press

the

ON/OFF

key.

3. Press

“#51.”

The

ON/OFF

LED remains lit.

To stop using a headset:

Repeat the preceding steps.

Hardware Requirements

• Headsets are not provided with the DBS; they must be purchased

separately.

• Most commercially available headsets (with ECM mike transducers) can

be used.

Considerations

• Headset Operation is not available with SLT telephones.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands