Panasonic VB-44210G User Manual Download Page 181 | Manualshive

Page: 181 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-65

Multi-Line (ML) Appearances

(CPC-AII and CPC-B Version 2.0 or higher)

Description

You can make and receive both CO line calls and Intercom Calls using a
Multi-Line (ML) key. Each extension can have up to 24Multi-Line keys. The
Attendant can have up to 24 Multi-Line keys.

See “ML/MCO Separation” (page 4-66) for information on assigning both
ML and MCO keys to the same system (CPC-AII and CPC-B Version 4 or
higher).

Operation

Related Programming

• FF1 (System): Least Cost Routing (LCR) Access

• FF2 (Trunks): Pooled Trunk Access for Group “9”

• FF2 (Trunks): Pooled Trunk Access for Group “81-86”

• FF3 (Extension): Forced Least Cost Routing

• FF5 (Keys): FF Key Assignment (all)

• FF8 (LCR) LCR Settings (all)

Considerations

• A Multi-Line key will ring for incoming CO calls, Intercom Calls, recall

calls, and call-forward calls.

Operation

Action

To originate a trunk call

Press an idle ML key.

The key blinks (green) as the call is
made.

To place a call on Exclusive Hold (page 4-37)

Press the ML key.

To place a call on System Hold (page 4-18)

Press the

HOLD

key.

To transfer a call

Press

HOLD

, dial the destination exten-

sion, then press

PROG

.

«
...
179
180
181
182
183
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Xblue Networks Pages: 241

Brand: Paradyne Pages: 4

KX-T7400 Series

Brand: Panasonic Pages: 1

FREELANCE XC 1500

Brand: BT Pages: 2

Brand: Xblue Networks Pages: 121

Box Design BT Box S2

Brand: Pro-Ject Audio Systems Pages: 6

Brand: Vicon Pages: 10

3600 Series 3618

Brand: Videx Pages: 8

Brand: Crestron Pages: 26

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 18

Brand: RCA Pages: 19

Brand: Hitachi Pages: 151

SelecSet 900 Series

Brand: Hitachi Pages: 187

Brand: Hitachi Pages: 189

Brand: AEG Pages: 8

Brand: AEG Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands