manualshive.com logo in svg

Panasonic VB-44210G, User Manual

The Panasonic VB-44210G User Manual is essential for maximizing the potential of your phone system. This comprehensive manual provides step-by-step instructions and troubleshooting tips, ensuring a seamless user experience. Download it for free from manualshive.com and unleash the full capabilities of your Panasonic VB-44210G.

Share
Download
background image

Chapter 4. Key Telephone Features

Section 700 - Operation

 

4-18

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• FF1 (System): Non-Appearing Central Office Line Hold

Considerations

• When using an outside line for which there is no line key on your 

extension, press the 

HOLD

 key to place the call on hold, and then press a 

vacant line key. Release the held call by pressing 

HOLD

 again. (System 

programming determines whether the call will be placed on Exclusive 
Trunk Hold or System Trunk Hold.)

• A held call will recall if it is not retrieved before the Hold Recall Timer 

expires. “Hold Recall #XX” (where “XX” is the outside line number) 
appears on the display if a call has been held beyond the time limit. 

• If you press the 

HOLD

 key during a conference with two outside lines, 

both outside lines will be placed on hold.

• If your system is set for onhook transfer and you have placed an outside 

call on hold, and you then make an Intercom Call, make sure the other 
extension hangs up before you do. If you hang up before the other 
extension, 

the held outside line will be transferred to that extension

. 

(Pressing 

FLASH

 releases the extension.)

• The DBS can provide music-on-hold to callers placed on hold. See 

“Music-On-Hold” (page 3-34) for more information.

System Hold

Description

Using System Hold, you can place either an outside call or an Intercom Call 
on hold. 

A call placed on System Hold can be retrieved from any extension.

Operation

To place a call on System Hold:

Press the 

HOLD

 key.

• The line LED being used for the call flashes green.

• The phone issues intercom dial tone.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Panasonic KX-TG8011E Quick Manual preview
KX-TG8011E
Brand: Panasonic Pages: 10
3Com VCX Installation And Configuration Manual preview
VCX
Brand: 3Com Pages: 84
3Com SuperStack 3 NBX Administrator'S Manual preview
SuperStack 3 NBX
Brand: 3Com Pages: 496
3CX Nx 32 Quick Start Manual preview
Nx 32
Brand: 3CX Pages: 15
JabloCom JabloPhone GDP-04 User Manual preview
JabloPhone GDP-04
Brand: JabloCom Pages: 12
Uniden DXAI5688-2 - DXAI Cordless Phone Manual Del Usuario preview
DXAI5688-2 - DXAI Cordless Phone
Brand: Uniden Pages: 68
Uniden DXAI4288-2 Guide Utilisateur preview
DXAI4288-2
Brand: Uniden Pages: 72
Garmin GPSMAP 67 Owner'S Manual preview
GPSMAP 67
Brand: Garmin Pages: 60
Roadpost China oneRoam International Cellular User Manual preview
China oneRoam International Cellular
Brand: Roadpost Pages: 8
ANT UNO G8 Series User Manual preview
UNO G8 Series
Brand: ANT Pages: 25
Landscape Vibrations LV-SA250 Installation Manual preview
LV-SA250
Brand: Landscape Vibrations Pages: 8
Trevi SB 8350TV User Manual preview
SB 8350TV
Brand: Trevi Pages: 24
WaterGroup E35TFC-2SF Installation, Operation And Service Manual preview
E35TFC-2SF
Brand: WaterGroup Pages: 24
Panasonic SC-UA4 Operating Instructions Manual preview
SC-UA4
Brand: Panasonic Pages: 68
Panasonic SC-PM251 Operating Instructions Manual preview
SC-PM251
Brand: Panasonic Pages: 18
Panasonic SA-AK350E Service Manual preview
SA-AK350E
Brand: Panasonic Pages: 100
Harman JBL QUANTUM Stream Talk Owner'S Manual preview
JBL QUANTUM Stream Talk
Brand: Harman Pages: 15
base engineering FWG09 Assembly Instructions Manual preview
FWG09
Brand: base engineering Pages: 26

Brands by name

Popular brands

Load more brands