Panasonic VB-44210G User Manual Download Page 182 | Manualshive

Page: 182 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-66

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• When a CO call or an Intercom Call arrives, a search begins for a Multi-

Line key not in use. The lower numbered FF keys will be searched first.
When a free Multi-Line key is found, the LED flashes green and the
extension rings.

• If another phone answers an incoming trunk call, the ML LED on your

extension goes off and the ringing stops, indicating that the Multi-Line key
on your telephone is no longer in use.

• When dialing an extension number, the system automatically selects the

free Multi-Line key with the lowest number.

• If the CO line or held extension does not respond before the Recall Timer

expires, the extension rings and the Multi-Line key flashes green.

• If LCR is enabled, ML keys can be assigned for trunk group 89. However,

the FF keys will not light.

ML/MCO Separation

(CPC-AII and CPC-B Version 4.0 or higher)

Description

Beginning with CPC-B Version 4, each extension can have either MCO or
ML keys. In previous software versions, MCO or ML keys were only
available on a system-wide basis, and the type of key that was available
differed according to the software release. Table 4-7 contains definitions of
MCO and ML keys. Table 4-8 shows MCO/ML availability with previous
releases.

Table 4-8. MCO/ML availability

Related Programming

• FF3 (Extension): ML/MCO Separation

• FF5 (Keys): FF Key Assignments (all)

CPC Version

Type of
Key

CPC-A

MCO only

CPC-B 1.0

MCO only

CPC-B 2.0 - 3.1

ML only

CPC-AII and CPC-B
4.0 and above

MCO or ML

«
...
180
181
182
183
184
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 6

Brand: 3Com Pages: 3

Brand: 3Com Pages: 2

Brand: Samsung Pages: 60

Brand: Samsung Pages: 2

Brand: Samsung Pages: 24

Brand: Samsung Pages: 22

Brand: Samsung Pages: 23

Brand: Nady Systems Pages: 10

Brand: Nady Systems Pages: 19

Brand: Gigaset Pages: 15

Brand: FITNESS AUDIO Pages: 12

Brand: Uniden Pages: 64

Jitterbug Smart2

Brand: GreatCall Pages: 21

Brand: Topcom Pages: 21

900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting...

Brand: Radio Shack Pages: 24

Brand: Aiwa Pages: 68

Brand: Aastra Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands