Panasonic VB-44210G User Manual Download Page 86 | Manualshive

Page: 86 / 394

background image

Chapter 3. System Features

Section 700 - Operation

Page 3-40

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

from an extension, give instructions to an entire group, or communicate with
several people at once. If an external paging system is connected to your
system, pages can also be sent through its speakers.

Beginning with CPC-B Version 3.1, the Paging feature can also be
programmed to time out after sixty seconds. When a page call times out, a
busy tone is sent to the extension that initiated the page.

Operation

To use the Paging feature:

1. Pick up the handset.

2. Press “#,” then enter the number of the desired Paging Group (00-07).

The

EXT

LED lights.

3. Make your announcement.

4. Replace the handset.

Related Programming

• FF1 (System): Page Duration (CPC AII and CPC-B Version 3.1 or higher)

• FF1 (System): External Page Interface Control for Paging Groups

• FF3 (Extension): Extension Page Group

Hardware Requirements

• External relays and an amplifier are required for external paging.

Considerations

• If an external paging system has been connected to Paging Groups 00-07,

pages can be made through the external speakers. Voice Paging can also be
heard over the extensions in groups 00-07.

• An extension can belong to more than one paging group.

• A maximum of eight Paging Groups can be assigned to a system.

• Only one page may be performed at a time with one exception. Pages to

group 00 always take priority. If you page group 00 while another
extension is paging group 01-07, the other page terminates. The other
pager receives busy and “Page Overridden” displays on the telephone.

«
...
84
85
86
87
88
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 289

Brand: Panasonic Pages: 60

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 36

T-Mobile KX-HDV130

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 8

KXDT346 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 5

KXDT321 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 24

DECT Portable Station KX-TCA256

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 18

Brand: i-onik Pages: 6

Brand: i-MOBIL Pages: 10

Brand: iHome Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands