Panasonic VB-44210G User Manual Download Page 111 | Manualshive

Page: 111 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-65

Related Programming

• FF1 (System): Extension Class of Service Setting

• FF1 (System): Ring Patterns for UNA Terminals (M, C, & B)

• FF3 (Extension): Extension Class of Service Assignment

• FF4 (Ringing and Hunt Groups): CO Day Ring Assignment

• FF4 (Ringing and Hunt Groups): CO Night Ring Assignment

Hardware Requirements

• An external ringing device is not provided with the DBS. It can be

purchased separately from an electronics dealer.

• External paging speakers are not provided with the DBS; they must be

purchased separately.

Considerations

• With CPC-A and CPC-AII, extension port 73 is used to assign ringing to

an external page/UNA interface.

• With CPC-B, extension port 145 is used to assign ringing to an external

page/UNA interface.

Voice Mail Ringing

(CPC-AII and CPC-B Version 3.1 or higher)

Description

The Voice Mail Ringing feature allows calls from a DBS Automated
Attendant or from an ACD port to ring an extension with the same ring tone
as a CO trunk. The ring pattern is selected in the Extension Distinctive
Ringing program. If a distinctive ringing pattern is not specified, the ringing
pattern will be two seconds on/two seconds off.

Related Programming

• FF3 (Extension): Extension Ring Pattern

«
...
109
110
111
112
113
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Jensen Pages: 2

Brand: Sprint Pages: 44

Hydro-Guard HG-3

Brand: Mueller Pages: 7

Brand: Laser Pages: 3

Brand: Wayne Pages: 1

Brand: Aastra Pages: 20

Brand: Pattfield Pages: 94

Brand: 3SIXT Pages: 6

Brand: AT&T Pages: 15

Brand: OGATECH Pages: 144

Brand: Panasonic Pages: 48

Brand: RCA Pages: 20

Brand: RCA Pages: 22

Brand: Craig Pages: 12

Brand: Kraun Pages: 2

Brand: Gigaset Pages: 21

Brand: JVC Pages: 32

Brand: JVC Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands