manualshive.com logo in svg

Omron OMNUC G5 R88D-KN series, User Manual

Share
Download
Omron OMNUC G5 R88D-KN series User Manual Download Page 411

11-18

11-4 Troubleshooting

OMNUC G5-Series AC Servo Drives Users Manual (Built-in MECHATROLINK-II communications type)

  11

Error and Maintenance

21

Encoder 
communications error

Occurs during operation.

• The encoder is 

disconnected.

• Connector contacts 

are faulty.

• Fix the locations that 

are disconnected.

• Wire correctly.

• The encoder is wired 

incorrectly.

• Wire correctly.

• The encoder is 

damaged.

• Replace the motor.

• The drive is faulty.

• Replace the Servo Drive.

• The  motor  is 

mechanically held.

• If the motor shaft is 

held, release it.

23

Encoder 
communications data 
error

Occurs when the power 
supply is turned ON.
Or, occurs during 
operation.

• The encoder signal line 

is wired incorrectly.

• Wire correctly.

• Noise on the encoder 

wiring causes incorrect 
operation.

• Take measures 

against noise on the 
encoder wiring.

• The encoder power 

supply voltage has 
dropped (especially 
when the cable is 
long.)

• Provide the required 

encoder power supply 
voltage (5 VDC 

 5%).

24

Error counter overflow

Occurs when the motor 
does not rotate even when 
command pulses are 
input.

• The motor power line 

or the encoder wiring is 
incorrect.

• Wire correctly.

• The  motor  is 

mechanically held.

• If the motor shaft is 

held, release it.

• Release the 

electromagnetic brake.

• Control PCB error

• Replace the Servo Drive.

Occurs during high-speed 
rotation.

• The motor power line 

or the encoder wiring is 
incorrect.

• Wire correctly.

Occurs when a long string 
of command pulses is 
given.

• Gain adjustment is 

insufficient.

• Adjust the gain.

• The acceleration/

deceleration is too 
rapid.

• Extend the 

acceleration/
deceleration times.

• The load is too large.

• Reduce the load.
• Select a suitable 

motor.

Occurs during operation.

• The set value for the 

Error Counter Overflow 
Level (Pn014) is 
exceeded.

• Increase the set value 

of Pn014.

• Reduce the rotation 

speed.

• Reduce the load.
• Extend the 

acceleration/
deceleration times.

Alarm 

number

Error conditions

Status when error 

occurs

Cause

Measures

Summary of Contents for OMNUC G5 R88D-KN series











































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands