manualshive.com logo in svg

NXP Semiconductors KE1xF Series, Reference Manual, Page: 1137 / 1483

Share
Download
NXP Semiconductors KE1xF Series Reference Manual Download Page 1137

42.5.1 Initialization

The following steps can be used to initialize the LPIT module

• Enable the protocol clock by setting the M_CEN bit in the MCR register.

NOTE

Writing to certain registers while M_CEN = 0 will lead to
assertion of transfer error for that bus access. These
registers are MSR, SETTEN, CLRTEN, TVAL, and
TCTRL. Writing to CVAL and Reserved registers will
generate a transfer error irrespective of M_CEN bit value.
Reads to these registers can happen irrespective of M_CEN
bit value.

• Wait for 4 protocol clock cycles to allow time for clock synchronization and reset de-

assertion.

• For each timer channel that is to be enabled, configure the timer mode of operation

(MODE bits), Trigger source selection (TRG_SEL & TRG_SRC) and Trigger
control bits (TROT, TSOT, TSOI bits) in the TCTRLn register.

• Configure the channels that are to be chained by setting the CHAIN bit in the

corresponding channel's TCTRLn register.

• For channels configured in Compare Mode, set the timer timeout value by

programming the appropriate value in TVAL register for those channels.

• Configure TIEn bits in MIER register for those channels which are required to

generate interrupt on timer timeout.

• Configure the low power mode functionality of the module by setting the DBG_EN

and DOZE_EN bits in the MCR register. This is common to all timer channels.

• Enable the channel timers by setting the corresponding T_EN bit in the

corresponding channel's TCRTLn register.

• For channels configured in Capture Mode, the timer value can be read from TVALn

register when channel timeout occurs.

• At any time, the current value of the timer for any channel can be read by reading the

corresponding channel's CVALn register.

• The timer interrupt flag bits (TIFn) in MSR register get asserted on timer timeout.

These bits can be cleared by writing '1' to them.

42.5.2 Timer Modes

The timer mode is configured by setting an appropriate value in the MODE bits in
TCTRLn register. The timer modes supported are:

Chapter 42 Low-power Periodic Interrupt Timer (LPIT)

Kinetis KE1xF Sub-Family Reference Manual, Rev. 4, 06/2019

NXP Semiconductors

1137

Summary of Contents for KE1xF Series












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments