manualshive.com logo in svg

Hitachi H8/3020, Hardware Manual

The Hitachi H8/3020 Hardware Manual is a comprehensive user guide that provides detailed instructions on operating and optimizing your H8/3020 device. Download this free manual from manualshive.com to explore in-depth information, troubleshoot issues, and make the most out of your product's advanced features.

Share
Download
background image

viii

13.2.3 A/D Control Register (ADCR).............................................................................. 415

13.3

CPU Interface ..................................................................................................................... 416

13.4

Operation ............................................................................................................................ 417
13.4.1 Single Mode (SCAN = 0)...................................................................................... 417
13.4.2 Scan Mode (SCAN = 1) ........................................................................................ 419
13.4.3 Input Sampling and A/D Conversion Time .......................................................... 421
13.4.4 External Trigger Input Timing .............................................................................. 422

13.5

Interrupts ............................................................................................................................ 423

13.6 Usage Notes .......................................................................................................................... 423

Section 14 RAM

.................................................................................................................... 429

14.1

Overview ............................................................................................................................ 429
14.1.1 Block Diagram ...................................................................................................... 430
14.1.2 Register Configuration .......................................................................................... 430

14.2

System Control Register (SYSCR) .................................................................................... 431

14.3

Operation ............................................................................................................................ 432

Section 15 ROM

.................................................................................................................... 433

15.1 Features .............................................................................................................................. 433
15.2 Overview ............................................................................................................................ 434

15.2.1 Block 

Diagram ...................................................................................................... 434

15.2.2 Mode 

Transitions .................................................................................................. 435

15.2.3  On-Board Programming Modes............................................................................ 436
15.2.4  Flash Memory Emulation in RAM........................................................................ 438
15.2.5  Differences between Boot Mode and User Program Mode .................................. 439
15.2.6 Block 

Configuration.............................................................................................. 440

15.3 Pin 

Configuration ............................................................................................................... 440

15.4 Register 

Configuration ....................................................................................................... 441

15.5 Register 

Descriptions.......................................................................................................... 441

15.5.1  Flash Memory Control Register 1 (FLMCR1)...................................................... 441
15.5.2  Flash Memory Control Register 2 (FLMCR2)...................................................... 444
15.5.3  Erase Block Register 1 (EBR1) ............................................................................ 445
15.5.4  Erase Block Register 2 (EBR2) ............................................................................ 446
15.5.5  RAM Emulation Register (RAMER).................................................................... 447
15.5.6  Differences from H8/3039 F-ZTAT Series ........................................................... 449

15.6  On-Board Programming Modes ......................................................................................... 450

15.6.1 Boot 

Mode............................................................................................................. 451

15.6.2  User Program Mode .............................................................................................. 456

15.7  Programming/Erasing Flash Memory ................................................................................ 458

15.7.1 Program 

Mode....................................................................................................... 459

15.7.2 Program-Verify 

Mode ........................................................................................... 460

15.7.3  Notes on Program/Program-Verify Procedure...................................................... 460
15.7.4 Erase 

Mode............................................................................................................ 465

Summary of Contents for H8/3020



































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3020

Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
RME Audio AI4S-192 AIO User Manual preview
AI4S-192 AIO
Brand: RME Audio Pages: 7
Juniper MX104 Quick Start Manual preview
MX104
Brand: Juniper Pages: 30
EK-Quantum 3831109836897 User Manual preview
3831109836897
Brand: EK-Quantum Pages: 14
Paradyne Hotwire 7996 User Manual preview
Hotwire 7996
Brand: Paradyne Pages: 46
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Brand: Forcepoint Pages: 2
SonicWALL Internet Security Appliances Administrator'S Manual preview
Internet Security Appliances
Brand: SonicWALL Pages: 293
ekwb EK-Quantum Vector FE RTX 3080 User Manual preview
EK-Quantum Vector FE RTX 3080
Brand: ekwb Pages: 20
Xaoc Devices NIN Operator'S Manual preview
NIN
Brand: Xaoc Devices Pages: 4
Compaq ProLiant 4500 Quick Start Manual preview
ProLiant 4500
Brand: Compaq Pages: 2
Maco RUSTICO 13321 Installation Instructions Manual preview
RUSTICO 13321
Brand: Maco Pages: 8
Icop VMXP-6453 User Manual preview
VMXP-6453
Brand: Icop Pages: 31
Acconeer XE132 Getting Started Manual preview
XE132
Brand: Acconeer Pages: 13
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Brand: Cambium Networks Pages: 155

Brands by name

Popular brands

Load more brands