manualshive.com logo in svg

Hitachi H8/3020, Hardware Manual

The Hitachi H8/3020 Hardware Manual is a comprehensive user guide that provides detailed instructions on operating and optimizing your H8/3020 device. Download this free manual from manualshive.com to explore in-depth information, troubleshoot issues, and make the most out of your product's advanced features.

Share
Download
background image

vii

11.2.1 Receive Shift Register (RSR)................................................................................ 327
11.2.2 Receive Data Register (RDR) ............................................................................... 327
11.2.3 Transmit Shift Register (TSR) .............................................................................. 328
11.2.4 Transmit Data Register (TDR).............................................................................. 328
11.2.5 Serial Mode Register (SMR)................................................................................. 329
11.2.6 Serial Control Register (SCR)............................................................................... 333
11.2.7 Serial Status Register (SSR).................................................................................. 337
11.2.8 Bit Rate Register (BRR)........................................................................................ 341

11.3

Operation ............................................................................................................................ 350
11.3.1 Overview ............................................................................................................... 350
11.3.2 Operation in Asynchronous Mode ........................................................................ 352
11.3.3 Multiprocessor Communication............................................................................ 361
11.3.4 Synchronous Operation ......................................................................................... 368

11.4

SCI Interrupts ..................................................................................................................... 377

11.5

Usage Notes........................................................................................................................ 378

Section 12 Smart Card Interface

...................................................................................... 383

12.1 Overview ............................................................................................................................ 383

12.1.1 Features ................................................................................................................. 383
12.1.2 Block 

Diagram ...................................................................................................... 384

12.1.3 Pin 

Configuration .................................................................................................. 385

12.1.4 Register 

Configuration .......................................................................................... 385

12.2 Register 

Descriptions.......................................................................................................... 386

12.2.1  Smart Card Mode Register (SCMR) ..................................................................... 386
12.2.2  Serial Status Register (SSR).................................................................................. 388

12.3 Operation ............................................................................................................................ 390

12.3.1 Overview ............................................................................................................... 390
12.3.2 Pin 

Connections .................................................................................................... 390

12.3.3 Data 

Format........................................................................................................... 392

12.3.4 Register 

Settings.................................................................................................... 394

12.3.5 Clock ..................................................................................................................... 396
12.3.6  Data Transfer Operations ...................................................................................... 398

12.4 Usage 

Note ......................................................................................................................... 404

Section 13 A/D Converter

.................................................................................................. 407

13.1

Overview ............................................................................................................................ 407
13.1.1 Features ................................................................................................................. 407
13.1.2 Block Diagram ...................................................................................................... 408
13.1.3 Pin Configuration .................................................................................................. 409
13.1.4 Register Configuration .......................................................................................... 410

13.2

Register Descriptions.......................................................................................................... 411
13.2.1 A/D Data Registers A to D (ADDRA to ADDRD) .............................................. 411
13.2.2 A/D Control/Status Register (ADCSR) ................................................................ 412

Summary of Contents for H8/3020



































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3020

Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Nvidia nForce 680I LT SLI Hardware User Manual preview
nForce 680I LT SLI
Brand: Nvidia Pages: 80
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
Holtek HT68F30 Manual preview
HT68F30
Brand: Holtek Pages: 280
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Brand: 7th Sense Pages: 148
Riverbed Cascade Express Installation Manual preview
Cascade Express
Brand: Riverbed Pages: 92
Tektronix 7B87 Instruction Manual preview
7B87
Brand: Tektronix Pages: 143
TRENDnet TEG-S3M8S15 Specifications preview
TEG-S3M8S15
Brand: TRENDnet Pages: 2
abaco systems PEX430 Hardware Reference Manual preview
PEX430
Brand: abaco systems Pages: 51
MikroTik AP Staging Manual preview
AP
Brand: MikroTik Pages: 7
NZXT H7 ELITE Manual preview
H7 ELITE
Brand: NZXT Pages: 38

Brands by name

Popular brands

Load more brands