Hi-Target Surveying Instrument ZTS-360R Manual Download Page 44

Page: 44 / 143

5. Angle mode

The instrument would enter the Angle Mode automatically

after switched on. You can also enter this Mode by pressing

[ANG] under basic measurement mode. This Mode involves

three pages switched by the key [F4]. Their functions are

explained as followed:

Vz:

HR:

Vmode

278°12′23″

159°54′05″

R/L

H-Bz

3/3

Vz:

HR:

Hset

278°12′23″

159°54′05″

0set

Save

1/3

Vz:

HR:

278°12′23″

159°54′05″

Rep

Hold

2/3

[F4]

5.1 Save

Function: Save the current angle to selected measured file.

●

After press [F1], the interface of “Information” appears

(if you haven’t select measured file, there will be a

interface of “Select file (.MEA)” to let you select file.),

which needs you the point name (Pt.N) ,Code and

target height (T.H). The number of “Pt.N” defaults to

added 1. The code is input according to your need, but

the target height according to actual situation. You can

press [ENT] to save data to measured file.

When the compensation value is over, the instrument tips “Tilt

over!”, and the angle data can’t be saved.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands