Hi-Target Surveying Instrument ZTS-360R Manual Download Page 25

Page: 25 / 143

STA

Set coordinates for station

P2/3

Display the third page of the soft key

functions

Ofset

Start offset measurement (eccentric

measurement)

S.O

Stake out coordinates

Aver.

Set the times of average measurement

3/3

Display the first page of the soft key

functions

2.3.4 Explanation of saving data

If you have never selected the measurement file and your

first time to use the [Save] soft key, a dialogue box of ‘Select
file’ would appear to the screen. Mention that this is a good
chance for you to select all files that the instrument may use.

When finishing single measurement, a dialogue box asks

you to save the measured point and you may rename and code

the points or set target height. The key ‘ENT’ will save the

coordinates into measurement files, and the key [

★

] save the

coordinates in the measurement file and coordinate file at the

same time (according to the mention of the display).

If you choose not to edit points, the points would be saved

with the present name, elevation and code .After saving, the

name of the point is added by one.

2.4 Star key [

★

] mode

On the measurement interfaces, pressing the key [

★

](star

key) can lead to a page as shown below.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands