Hi-Target Surveying Instrument ZTS-360R Manual Download Page 101

Page: 101 / 143

Aim at the prism, then press [Meas] to measure the

horizontal distance from prism to prism and enter the interface

of “REM-Base”;

REM-Base

VZ:

Select

HR:
VD:

77°18′33″

169°11′14″

0.000 m

Aim at the reference point and press [Select] to enter the

dialog of ‘REM-Altitude’

REM-Altitude

VZ:

SetVA

HR:
VD:

77°18′33″

169°11′14″

0.000 m

Then turn the telescope up and down. The elevation

difference between the target and the reference point is displayed

in the VD column.

REM-Altitude

VZ:

SetVA

HR:
VD:

77°18′33″

169°11′14″

1.657 m

After the measurement, you have three opts:

[Set VA] :to re-enter the ‘REM-Altitude’ page.

[HDist] :to re-measure the horizontal distance;

[ESC]:to quit REM measurement.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands