Hi-Target Surveying Instrument ZTS-360R Manual Download Page 108

Page: 108 / 143

of “Project-Survey”; press [Meas] to start measuring. After the

measurement, the deviated length(X), distance(Y) and altitude

difference (Z) are displayed on the screen.

Project-Survey

166°40′39″

Meas

Turn

HR:

0.300

T.H

-1.079

-0.002

Press [F4](Turn)→

Project-Survey

SD:

166°40′39″

Meas

Turn

HD:

VD:

HR:

0.754

T.H

-0.754

0.002

The key [T.H] is used for re-inputting target height; the key

[Turn] using for switching the display between “X,Y,Z” or
“SD,HD,VD”;

9.4.6 Roadway

See reference in chapter 10. Roadway

9.5 Options

Menu of options:

Options

1. Unit options
2. Mode options
3. Other options

Press [1] to enter the interface of “options”

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands