Hi-Target Surveying Instrument ZTS-360R Manual Download Page 88

Page: 88 / 143



Select a measurement file in the file list, and press

[ENT] to display the data list as shown in picture below.

The left side of list is point name, and right is data type.

ST1 [STA]

BS01

Del

[BS]

View

S1
S2

[ANG]

[DIST]

[COO]



Pressing [View] can display the information of selected

data. Here, as an example of station data, as shown in

picture below. Press [F4] (Turn) to view the data in the

second page.

STA：ST1
Code：tree

Last

First

Edit

Turn

     N：328.263
     E：656.365
     Z：1.236



Press [Edit] to enter the interface of “Information”, and

you can just edit point name (Pt.n), code (Code).and

target height (T.H)(Notice: can’t edit the data of station

and backsight), then back to the last interface;



Pressing [First] can display the information of the first

piece data;



Pressing [Last] can display the information of the last

piece data;



Pressing [

▲

] can display the information of the

previous piece data;



Pressing [

▼

] can display the information of the next

piece data;

●Press [Search] to enter the condition input interface, and

you can input the point name which you want and press

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands