Hi-Target Surveying Instrument ZTS-360R Manual Download Page 31

Page: 31 / 143

operations in 3.5, press soft key [Enter] to move inserter down to
the ‘PPM’ column to enter the value.

Temp.:
Press:

Signal

℃

hpa

Clear

B.S

Enter

Prism c:

PPM:

ppm

Signal

1013

Temp.:
Press:

Signal

℃

hpa

Clear

B.S

Enter

Prism c:

PPM:

ppm

Signal

1013

0
3

3.6.2 Calculate the Atmospheric Correction out with
temperature and pressure sensor

First, measure the temperature and pressure around the

station in advance.

e.g. Temp: +25

℃

atm:1017.5

Press soft key [Enter] to move inserter to the ‘Temp’

column and type in ‘25.0’;

Press soft key [Enter] to move inserter to the ‘Press’

column and type in ‘1017.5’;

Press soft key [Enter] to move the inserter to the [prism c]

column;

(the‘PPM’ column now displays 3)
Press [ENT] to save the parameter. Our system will display

‘Record: ***(name of the point)’ and exit the dialogue box. The
point is saved now.

3.7 The Correction of the Atmospheric refraction
and the Earth Curvature

When measuring horizontal distance and elevation, our

instrument corrects the atmospheric refraction and the earth

curvature automatically.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands