Hi-Target Surveying Instrument ZTS-360R Manual Download Page 52

Page: 52 / 143

dhd:

is to stake out the difference between horizontal

distance measured and it expected . A positive result indicates

that the measured horizontal distance is greater than the

expectation value. The lens should be moved to the instrument.

dvd:

is to stake out the difference between elevation

difference measured and it expected. A positive result indicates

that the measured elevation difference is greater than the

expectation value. The lens should be moved downwards

(excavation).

Every time finishing the stakeout, press [F4] to enter the

second page , and you can press [F2] to continue staking out or

press [DIST] to return to the distance measurement mode.

m/f/i:

switch the units of the distance displayed between

“meter”, “ feet”, “feet .inch”.

Other instructions: “

” is the current distance

measurement mode. Among them, the “

” indicates

measuring with prism, and the “

”indicates measuring

without prism.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands