Hi-Target Surveying Instrument ZTS-360R Manual Download Page 109

Page: 109 / 143

Unit options

1.Type of feet

1/2

2.Unit (Angle)
3.Unit (Length)

Unit options

1.Unit(Temp.)

2/2

2.Unit(Press)

Press [2] to enter the interface of “Mode options”:

Mode options

1.EDM Mode
2.NEZ option
3.VA mode

Press [3], enter the interface of “Other options”:

Other options

1.Mini Angle

1/2

2.Auto shut off
3.Rectangle Beep

Other options

1. K option

2/2

2. Beep

Taking “EDM” for example, the interface as shown below:

EDM Mode

[1.Single ]

Enter

2.Rept
3.Cont
4.Track

Exit

Press [

▲

] or [

▼

] to move the “>” to the options needed,

then press [Enter] to receive the select , and save it to system file.

After shut on the instrument next, the mode defaults as the

selected mode. The other settings are same as “EDM Mode”,

not

tired in words here.

9.6 Adjust

Press [MENU]→[F4] →[1](Adjust) to enter the interface of

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands