Hi-Target Surveying Instrument ZTS-360R Manual Download Page 100

Page: 100 / 143

Ins.&Tar.” To input instrument height and target height, then

press [ENT] to enter the interface of “REM-Prism”;

REM-Prism

VZ:

Mode

Meas

Enter

HR:

HD:

77°18′33″

169°11′14″

Aim at prism, then press [Meas] to measure the horizontal

distance between target point and instrument. Press [Enter] to

enter the interface of “REM-Ground to target”;

REM-Ground to target

VZ:

T.H

HR:
VD:

77°18′33″

169°11′14″

0.000 m

Then, turn the telescope up and down to aim at the target

point. The VD column displays the elevation difference from the

ground to the target point.

After measurement, you may choose from three opts:

[T.H] :to alter the target height;

[Hdist] :to re-measure horizontal distance;

[ESC]:to quit REM measurement.

You can choice according to the actual usage.

9.4.1.2 “Without T.H”

After select this mode, enter the interface of “REM-Prism”:

REM-Prism

VZ:

Mode

Meas

Enter

HR:

HD:

77°18′33″

169°11′14″

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands