Hi-Target Surveying Instrument ZTS-360R Manual Download Page 89

Page: 89 / 143

[Enter] ,then the system searches the data from the first piece (all

name matched). If searching it, the cursor will be at the point , or

will tip and back to the first piece data.

●press [Del] to enter the interface of “Del”,if select [Yes],

the data you selected will be deleted or press [Exit] back to the

data list.

9.3.2 Import

As the format of file in the instrument is binary, the

External data must be imported to instrument. This function can

import the external ASCII coordinate file and code file to

instrument to save in binary format. The types of file you

selected are distinguished each other by extension. So, you must

be careful about the file type, or you will import unsuccessfully.

The interface of importing file as shown in picture below:

Type of import

1. Import from PC
2. Import from USB

9.3.2.1 Import from PC

This function needs port to connect PC and instrument, but

the transfer software must be installed on the PC to end data, or

the instrument can’ receive. Press [Fileman]→ [2](Import)→

[1.Import from PC],then the interface of “Import data” as shown

below:

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands