Hi-Target Surveying Instrument ZTS-360R Manual Download Page 102

Page: 102 / 143

9.4.2 MLM

dHD

dVD

dSD

Prism B

Prism A

Prism C

Instrument

Diagram of “MLM”

Measure the horizontal distance (dHD), slope distance

(dSD), elevation difference (dVD) and azimuth angle (dHD)

between two target. You may also input the coordinate or

retrieve coordinate from files to calculate the value.

There are two modes of ‘MLM’:

1.MLM (A-B,A-C): measure A-B, A-C, A-D…. i.e the

starting point is the reference point of all following points.

2.MLM (A-B, B-C): measure A-B, B-C, C-D…. i.e the

previous point is the reference point of all the other points.

You may also have to choose ‘Consider Grid scale’ or to

‘Ignore Grid scale’ before choosing measurement mode.

MLM (A-B, A-C):

Enter the interface of ‘MLM(A-B,A-C)-Step 1’;

MLM（A-B,A-C）-Step 1

VZ:

Coord.

T.H

Meas

Mode

HR:
HD:

55°29′34″

137°32′40″

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands