Hi-Target Surveying Instrument ZTS-360R Manual Download Page 26

Page: 26 / 143

Reflect :

Laser

Tilt

Light

Para.

Contrast:

☼

[☆] select file

▶

Settings from the star key(

★

) are as followed:

●

Adjust contrast : press [▲] and [▼];

●

Adjust background light of the screen : press [F4] to

open the backlight ,then press [◄] to adjust light;

●

Comp.: press [F2] to enter the display of electric

bubble , then press [F2] to set the compensator on or

off; pressing [◄] [►] can adjust the light of laser

plumb;

●

Reflect: Press [►] to set the reflector. The options of

reflector are switched between Prism ,Non- prism(NP)

and reflector board(RB);

●

Laser: press [F3] to on or off the laser;

●

Para.: Press the key [F4] to select ‘parameters’. You

can set settings of prism const, PPM value and

temperature and pressure, and view the signal. (The

setting of the distance measurement. After you input

the temperature and pressure, pressing [F1] can

automatically calculate the value of PPM, if you are not

satisfied with the value, you can input and save it). The

interface of picture as shown below:

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands