Hi-Target Surveying Instrument ZTS-360R Manual Download Page 67

Page: 67 / 143

9. Menu

In the basic measurement interface, press [MENU] to enter

the menu interface, then, press [F4] to enter the next page.

1.Surveying

1/2

2.Stake

3.Fileman

4.Program
5.Options

[F4]

1.Adjust
2.Config
3.Select CodeFile
4.Grid scale

5.Communication

On the every page of menu, you can press number key to

select. For example, if you press [1], the first option
“1.Surveying” will be done.

9.1 Surveying

Operation: press [MENU] to enter the first page of menu,

then press [1](Surveying):

Select file(.MEA&COO)

Num.

List

B.S

Enter

File：

AAA

[1]

1.Surveying

1/2

2.Stake
3.Fileman

4.Program

5.Options

Press [F4] to enter the interface of “Surveying”, then press

[F4] to turn to the second page.

1.Surveying

1/2

2.Stake

3.Fileman

4.Program
5.Options

[F4]

1.Adjust
2.Config
3.Select CodeFile
4.Grid scale

5.Communication

9.1.1 Operation

Select file for surveying to save the surveying data;

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands