Hi-Target Surveying Instrument ZTS-360R Manual Download Page 110

Page: 110 / 143

“Adjust”:

Adjust

1. Calibrate I.E
2. Calibrate TILT:X
3. Calibrate TILT:Y

9.6.1 Calibrate I.E

To adjust index error, the system will first ask you to ‘Aim

at a target F1’(face left). You may press [ENT] to confirm after
aiming, and the instrument will measure its vertical angle

automatically. The angle will be displayed for one second and
the system will ask you to ‘Aim at a target F2’(face right).
Following the same steps, the instrument will then calculate the

index error and display it.

Now press [ENT] to save the index error (calibration done),

otherwise press [ESC] to quit (previous I.E remains).

9.6.2 Calibrate TILT:X

When calibrating tilt, please make sure that the tilt is off

and the index error is little.

First,

lace the instrument as picture shown below with

collimator facing up. This will help screw C to adjust the

inclination of the instrument.

Enter the interface of tilt calibration:

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands