Hi-Target Surveying Instrument ZTS-360R Manual Download Page 46

Page: 46 / 143

5.4 Hold

Function:

Another method to set horizontal angle.

●

Turn around the alidade to the wanted horizontal angle

and press soft key [Hold], the turn around the alidade a
and the readout of horizontal angle is ‘hold’ and not
changing with turning the alidade again, the horizontal

angle remain the same.

●

After turning the alidade to aim at the target, press the

key [F1] to set horizontal angle at a new position.

Hold

Yes

HR：

156°38′54″

> Set?

5.5 Angle by repetition

Function:

Under right horizontal angle mode, you can

measure angle repeatedly.

1st meas.starts

2nd meas.starts

3rd meas.starts

3rd meas. End(avg. of 3 meas. Is displayed

2nd meas. End(avg. of 3 meas. Is displayed

1st meas.starts( angle between two points is displayed)

●

Enter the interface of angleoby repetition

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands