Hi-Target Surveying Instrument ZTS-360R Manual Download Page 50

Page: 50 / 143

6. Distance mode

Press [DIST] to enter the distance measurement mode,

which  has  two  interfaces  .  The  functions  of  first  interface  are
“Save”,  “Meas.”  and  “Mode”;  The  functions  of  the  second
interface  are  “Ofset”,  “S.O”  and  “m/f/i”.  The  two  interfaces

shown as below:

Vz:
HR:

Mode

278°12′23″
159°54′05″

Meas

Save

1/2

SD:

HD:

m
m

VD:

Vz:
HR:

m/f/i

278°12′23″
159°54′05″

S.O

Ofset

2/2

SD:

HD:

m
m

VD:

[F4]

6.1 Save

●

After press [F1], the interface of “Information” appears

(if you haven’t select measured file, there will be a

interface of “Select file (.MEA)” to let you select file.),

which needs you the point name (Pt.N) ,Code and

target height (T.H). The number of “Pt.N” defaults to

added 1. The code is input according to your need, but

the target height according to actual situation. You can

press [ENT] to save data to measured file.

●

When the compensation value is over, the instrument

tips “Tilt over!”, and the angle data can’t be saved.

6.2 Meas.

Measure distance and display slop distance, horizontal

distance, and elevation difference. Under the “cont” and “ track”,

you can press [ESC] to stop measuring.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands