Hi-Target Surveying Instrument ZTS-360R Manual Download Page 2

Page: 2 / 143

Preface

Thank you for purchasing our ZTS-360 Mini series total

station! This manual is your good helper, please read it before

operating the instrument and keep it properly.

Product Validation

In order to get our best service, please give the feedback

about the version, number, purchasing date of the instrument and

your valuable suggestions to us after you purchase our product.

We will attach great importance to every piece of advices

from you!

We will pay much attention to every detail of our products

！

We will make great efforts to provide better quality!

Notice: We reserve the right to change the technical

parameters during updating and improving our products and we

may not announce you in advance. The Pictures in this manual is

for reference only, please in kind prevail.

Summary of Contents for ZTS-360R
















































































































































Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands

Hi-Target Surveying Instrument ZTS-360R, Manual

Search results

Summary of Contents for ZTS-360R

Reviews:

Related manuals for ZTS-360R

Brands by name

Popular brands