background image

f ^ |   Assemble

 

Figure 87

•  

Reverse  input  and  input  clutch  assembly  into 
the transmission case.

A.  Index  the  3-4  clutch  plates  with  the  input 

internal  gear.

B.  M ake  sure  all  clutch  plates  are  fully 

engaged.

C.  When properly assembled, the reverse input 

clutch  housing  will  be  located  just  below 
the case oil pump face.

Figure 87  Installing  Input Clutch

2-4 Band Assembly

 

Figures 87 and 88

 

| y |   Inspect

•  

2-4 band assembly  (602) for damage or wear.

|h^h| 

Assemble

 

Figures 87 and 88

1.  Align  the  band  anchor  pin  end  with  the  case 

pin hole.

2.  Band anchor pin (41)  into the case.

•   Index the pin into the 2-4 band.

Figure 88 2-4  Band Assem bly -  Installed

Oil Pump Assembly

 

Figures 89 and 91

 

Remove or Disconnect

1.  Thrust washer (601).

2.  Pump cover to case  gasket  (6).
3.  Pump to case oil  seal  (5).
4.  Pump cover bolts  (233).
5.  Pump cover (215)  from pump body  (200).

Oil Pump Body

Figure 91

 

Disassemble

1.  Pump  slide  springs  (206  and 207).

CAUTION:  Springs  are  under  very  high

 

pressure.  Place  covering  over  spring  to

 

prevent possible injury.

A.  Compress  with needle nose pliers.

B.  Pull  straight out.

8

A

41

A  BAND ANCHOR  PIN  LOCATION

 

8  CASE, TRANSMISSION

 

41  PIN,  BAND ANCHOR

 

605  HOUSING  AND  DRUM  ASSEMBLY,  REVERSE

 

INPUT CLUTCH

 

621  HOUSING  AND  SHAFT ASSEMBLY,  INPUT

R H 0 1 8 1 -4 L 6 0 -E

Summary of Contents for S Series 1994
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: