![background image](http://html1.mh-extra.com/html/gmc/s-series-1994/s-series-1994_repair-manual_2235929389.webp)
• Rocker arm areas that contact the valve stems and
the socket areas that contact the ends of the push-
rods. These areas should be free of wear or dam
age.
• Rocker arm nuts.
• Pushrod ends for scoring, roughness, or bends.
— Roll the pushrod on a flat surface to determine
its straightness. If the rod is bent, the rod will
not roll freely. Replace if necessary.
HYDRAULIC LIFTERS
The type of hydraulic lifters used in this engine are
the roller type.
Hydraulic lifters are serviced only as an assembly.
No
internal parts are available.
Important
Whenever the camshaft needs to be replaced, a
new set of hydraulic lifters must also be installed.
CYLINDER HEAD
Cylinder head disassembly is covered in this proce
dure. Refer to SECTION 6A for information regarding
the following:
• Cleaning
• Inspection
• Measuring clearances
• Valve grinding
• Valve guide reconditioning
DISASSEMBLY
Remove or Disconnect (Figures 30 and 31)
Tool Required:
J 8062 Valve Spring Compressor
1. Valve keepers (20).
A. Compress the springs with J 8062 (figure 31).
B. Remove the keepers.
C. Remove J 8062.
2. Intake valve components (figure 30).
A. Cap (21)
20. Valve Keeper
21. Cap
22. Shield
23. O-Ring Seal
24. Seal
25. Damper
26. Spring
27. Intake Valve
28. Rotator
29. Exhaust Valve
B7609
B. Shield (22)
C. Seal (24)
D. Damper (25)
E. Spring (26)
3. Exhaust valve components (figure 30).
A. Rotator (28)
B. Shield (22)
C. Seal (24)
D. Damper (25)
E. Spring (26)
4. O-ring seals (23).
5. Valves (27 and 29).
• Place the valves in an organizer rack so they
can be replaced in their original position at
reassembly.
ROCKER ARM STUD REPLACEMENT
The 4.3L VIN Z engine can be equipped with two
different rocker arm stud configurations that require dif
ferent valve lash procedures.
If you have a 4.3L VIN Z engine that has screw-in
rocker arm studs with positive stop shoulders, you must
follow the replacement procedures outlined below under
“ Screw-In Studs.” No valve adjustment is necessary.
When the valve train requires service, you simply tight
en the rocker arm nuts to 27 N-m (20 ft. lbs).
If you have a 4.3L VIN Z engine that has pressed-in
rocker arm studs, you must follow the replacement pro
cedures outlined below under “ Pressed-ln Studs” and
the valve adjustment procedure outlined under “Valve
Adjustment.”
Screw-In Studs
Remove or Disconnect
Rocker arm stud by unscrewing.
|-^+| Install or Connect
NOTICE: Refer to “Notice” on page 6A3-1.
Summary of Contents for S Series 1994
