Garmin G2000 Pilot’s Guide for the Cessna T240
190-01263-01 Rev. A
SY
STEM
O
VER
VIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO & CNS
FLIGHT
MANA
GEMENT
HAZARD
AV
OID
ANCE
AFCS
ADDITIONAL FEA
TURES
APPENDICES
INDEX
568
Appendix A
System Message
Comments
NoN WGS84 WPt
– Do not
GPS for navigation to [xxxx]
The position of the selected waypoint [xxxxx] is not calculated based on the WGS84 map
reference datum and may be positioned in error as displayed. Do not use GPS to navigate to
the selected non-WGS84 waypoint.
tRAFFIC FAIL
– Traffic device
has failed.
The G2000 is no longer receiving data from the traffic system. The traffic device should be
serviced.
FAILeD PAtH
– A data path
has failed.
A data path connected to the GDU or the GIA 63/63W has failed.
LARGe MAG VARIANCe
–
Verify all course angles.
The GDU’s internal model cannot determine the exact magnetic variance for geographic
locations near the magnetic poles. Displayed magnetic course angles may differ from the
actual magnetic heading by more than 2°.
SCHeDULeR [#]
–
<message>.
Message criteria entered by the user.
SVt DISABLeD
–
Out of
available terrain region.
Synthetic Vision is disabled because the aircraft is not within the boundaries of the installed
terrain database.
SVt DISABLeD
– Terrain DB
resolution too low.
Synthetic Vision is disabled because a terrain database of sufficient resolution (9 arc-second
or better) is not currently installed.
teRRAIN DISABLeD
– Terrain
Awareness DB resolution too
low.
TAWS is disabled because a terrain database of sufficient resolution (9 arc-second or better)
is not currently installed.
tRN AUD FAIL
– Trn
Awareness audio source
unavailable.
TAWS is disabled because an aural alert audio source is unavailable.
tRN AUD CFG
– Trn
Awareness audio config error.
Service req’d.
TAWS is disabled because the audio configuration is invalid. The system should be serviced.
CHeCK CRS
– Database course
for LOC1 / [LOC ID] is [CRS]°.
Selected course for LOC1 differs from published localizer course by more than 10 degrees.
CHeCK CRS
– Database course
for LOC2 / [LOC ID] is [CRS]°.
Selected course for LOC2 differs from published localizer course by more than 10 degrees.
[PFD1 or MFD1]
CARD 1
ReM
– [PFD1 or MFD1] card 1
was removed. Reinsert card.
The SD card was removed from the top card slot of the PFD or MFD. The SD card needs to be
reinserted.
[PFD1 or MFD1]
CARD 2
ReM
– Card 2 was removed.
Reinsert card.
The SD card was removed from the bottom card slot of the PFD or MFD. The SD card needs
to be reinserted.
[PFD1 or MFD1]
CARD 1
eRR
– [PDF1 or MFD1] card 1
is invalid.
The SD card in the top card slot of the PFD or MFD contains invalid data.
[PFD1 or MFD1]
CARD 2
eRR
– [PFD1 or MFD1] Card 2
is invalid.
The SD card in the bottom card slot of the PFD or MFD contains invalid data.
[PFD1 or MFD1]
CARD 3
ReM
– Card 3 was removed.
Reinsert card.
The internal SD card was removed from the PFD or MFD. The system should be serviced.
This manual downloaded from http://www.manualowl.com