System Management |
75
Recovering from a Forgotten Enable Password
If you forget the enable password:
Figure 4-12. Renaming the startup-config
7
Reload the system.
reload
BOOT_ADMIN
8
Copy startup-config.bak to the
running config.
copy flash://startup-config.bak
running-config
EXEC Privilege
9
Remove all authentication statements
you might have for the console.
no authentication login
no password
LINE
10
Save the running-config.
copy running-config startup-config
EXEC Privilege
Step
Task
Command Syntax
Command Mode
1
Log onto the system via console.
2
Eject the secondary RPM if there is one.
3
Power-cycle the chassis by switching off all of the power modules and then switching them back on.
4
Abort bootup by sending the break
signal when prompted. See
Figure 4-10
.
Ctrl+Shift
+
6
5
Configure the system to ignore the
enable password on bootup.
Note:
This command only bypasses
the enable password once. You must
repeat this procedure to bypass it
again.
ignore enable-password
BOOT_USER
Figure 4-13. Ignoring the Enable Password
6
Reload the system.
reload
BOOT_USER
7
Configure a new enable password.
enable
{
secret
|
password
}
CONFIGURATION
8
Insert the secondary RPM.
Step
Task
Command Syntax
Command Mode
RPM0-CP BOOT_ADMIN # dir flash:
Directory of flash:
1 -rwx 11407411 Jun 09 2004 09:38:40 FTOS-EE3-5.3.1.1.bin
2 -rwx 4977 Jun 09 2004 09:38:38
startup-config.bak
***** Welcome to FTOS Boot Interface *****
Use "help" or "?" for more information.
BOOT_USER # ignore enable-password
Summary of Contents for Force10 E300
