Coreco PCVisionplus Hardware Reference Manual Download | Manualshive

Page: 86 / 206

background image

Registers

PCVisionplus



Hardware Reference

3–19

Rev 02; February 8, 2002

3.2.4 PCI Interrupt Control and Status (INTCTL) R/W

0

7

BADR0 + 0x38

0

0

0

0

0

0

0

0

8

15

Reserved

BINTEN

0

INTEN

1

1

1

1

INTCTL

16

23

Reserved

0

TAINT

MAINT

Reserved

BINTST

INTST

Reserved

24

31

0

0

0

0

0

0

0

0

This register provides a method for choosing conditions that produce an interrupt to the PCI bus, a method for view-
ing the cause of the interrupt, and a method for acknowledging (removing) the interrupt’s assertion. This register
must be used in conjunction with the many other interrupt enable and clear registers and bits on the PCVisionplus.
The following conditions could produce a PCI-bus interrupt: Bus Master Transfer Count reaches zero, Target Abort,
Master Abort, or a PCVisionplus interrupt defined in the INTENREG or AMINTEN registers. Always program bits
defined as zero or one to their respective values.

Bit

Mnemonic

Function

0–7

Reserved

Must be zero

8–11

Reserved

Must be one

12

INTEN

PCI Interrupt Enable

13

Reserved

Must be zero

14

BINTEN

Interrupt on Bus Master Transfer Done

15–16

Reserved

“Don’t Care”

17

INTST

PCI Interrupt Status

18

BINTST

Bus Master Interrupt Status

19

Reserved

“Don’t Care”

20

MAINT

Master Abort Interrupt Status

21

TAINT

Target Abort Interrupt Status

22

Reserved

Must be zero

23

Reserved

“Don’t Care”

24–31

Reserved

Must be zero

3.2.4.1 PCI Interrupt Enable (INTEN) R/W

This bit enables the interrupt source set by the INCON0, INCON1 and AMINTEN registers to generate an interrupt
on the PCI-bus.

INTEN

Function

0

Disable the PCVisionplus based interrupt

1

Enable the PCVisionplus based interrupt

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
84
85
86
87
88
...
»

Summary of Contents for PCVisionplus















































































































































































































Reviews:

No comments

Related manuals for PCVisionplus

Brand: Epson Pages: 87

Brand: CNET Pages: 26

Brand: ADLINK Technology Pages: 107

Brand: ADLINK Technology Pages: 110

Brand: NESS ID TECK Pages: 15

Brand: Videofied Pages: 6

Brand: Air Live Pages: 74

Brand: Accuris Pages: 38

Brand: United Electronic Industries Pages: 20

Brand: ADC Pages: 14

Brand: Zcom Pages: 5

GTX 460 1024MB GS-GLH

Brand: Gainward Pages: 2

Brand: i-tec Pages: 32

Brand: Sun Microsystems Pages: 62

Brand: Creative Pages: 22

DWL-500 - 11Mb Wireless LAN PCI Network Card

Brand: D-Link Pages: 80

Brand: JARLTECH Pages: 15

Brand: Jaton Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands