Coreco PCVisionplus Hardware Reference Manual Download Page 123 | Manualshive

Page: 123 / 206

background image

402-00005-00

Registers

3–56

Rev 02; February 8, 2002

3.4.12 PLL Programming Port (PLLPROG) R/W

0

7

BADR2 + 0x34

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

PLLSDATA

8

15

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

PCP_PLLPROG_32

16

23

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

24

31

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

This register is the serial data port for the programmable Phase-Locked Loop (PLL).

3.4.12.1 PLL Serial Data (PLLSDATA) R/W

The PLLSDATA bit is the serial data input and output to the PLL registers. The PLL is accessed through a serial
programming interface. Data is programmed using this register and the PLLCS bit in the INCON2 register. The PLL
registers and programming examples appear in Chapter 4.

3.4.13 DAC Programming Port (DACPROG) R/W

0

7

BADR2 + 0x38

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

DACSDATA

8

15

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

PCP_DACPROG_32

This register is the serial data port for the four programmable DACs. These DACs control the ADC Reference Volt-
ages, Clamping Voltage, and Sync Stripper frequency range.

3.4.13.1 DAC Serial Data (DACSDATA) R/W

The DACSDATA bit is the serial data input to the DAC registers. The DACs are accessed through a serial program-
ming interface. Data for each 13-bit DAC must be programmed 1 bit at a time using this register and the DACCS bit
in the INCON2 register. Refer to “DAC Programming” in Chapter 4.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
121
122
123
124
125
...
»

Summary of Contents for PCVisionplus















































































































































































































Reviews:

No comments

Related manuals for PCVisionplus

Brand: JARLTECH Pages: 31

Brand: SanDisk Pages: 2

Brand: StarTech.com Pages: 10

9800PRO - 128MB Dell - Radeon AGP 8x Vga DVI Tv-out DDR X2603

Brand: ATI Technologies Pages: 64

Universal 3 in 1 Reader/Writer

Brand: Dazzle Pages: 47

Brand: 3Dlabs Pages: 44

Brand: Gigabyte Pages: 36

Brand: ASIS Technologies Pages: 10

Brand: National Instruments Pages: 84

PISO-CAN-FD Series

Brand: ICP DAS USA Pages: 88

2126800 - Media Reader 7500

Brand: Adaptec Pages: 20

KAAN Standard Plus

Brand: Kobil Pages: 73

Brand: Velleman Pages: 2

Brand: Velleman Pages: 32

Brand: ADLINK Technology Pages: 210

Thunderbolt Pro P2

Brand: Sonnet Pages: 2

Brand: Glancetron Pages: 10

Brand: Iron logic Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands