Canon iR3570 Series, Service Manual

Page: 85 / 722

Chapter 2
2-11
F-2-42
2) Check if the machine wobbles while it is lying on the desk or the floor,
and tighten the adjusting screws if necessary.
- When it wobbles in the direction shown by the arrow A, tighten the screw
at the right side in the above picture.
- When it wobbles in the direction shown by the arrow B, tighten the screw
at the left side in the above picture.
F-2-43
3) Mount the cassettes 1 and 2.
2.2.5 Connecting the Cable
0007-5059
iR2270 / iR2870 / iR3570 / iR4570 / / / /
1) If you are installing a cassette pedestal, remove the lattice connector
cover, and fit the lattice connector [1] of the cassette pedestal to the
machine.
F-2-44
2) Connect the power plug to the power outlet.
1. Power supply voltage shall be +/-10% of the rating.
2. The amperage of the power supply must be as rated.
3. Before connecting the power plug, check to be sure that the main power
switch is off.
3) Turn on the main power switch.
- The machine issues a message to indicate that it is loading programs.
- The machine issues a message to indicate that its printer is getting ready for
a job.
Turning Off the Main Power
Whenever you have to turn off the main power, be sure to go through the fol-
lowing to avoid damage to the hard disk:
1. Hold down the control panel power switch for 3 sec or more.
2. Go through the instructions for the shut-down sequence shown on the dis-
play so that the main power switch may be turned off.
3. Turn off the main power switch.
2.2.6 Connecting the Cable
0010-2913
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N /
/ iR4570N / iR2230 / / iR3530 / / / / /
1) If you are installing a cassette pedestal, remove the lattice connector
cover, and fit the lattice connector [1] of the cassette pedestal to the
machine.
F-2-45
2) Connect the power plug to the power outlet.
1. Power supply voltage shall be +/-10% of the rating.
2. The amperage of the power supply must be as rated.
3. Before connecting the power plug, check to be sure that the main power
switch is off.
3) Turn on the main power switch.
- The machine issues a message to indicate that it is loading programs.
- The machine issues a message to indicate that its printer is getting ready for
a job.
Turning Off the Main Power
Whenever you have to turn off the main power, be sure to go through the fol-
lowing to avoid damage to the hard disk:
1. Hold down the control panel power switch for 3 sec or more.
2. Go through the instructions for the shut-down sequence shown on the dis-
play so that the main power switch may be turned off.
3. Turn off the main power switch.
2.2.7 Stirring Toner
0007-5062
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / iR3530 /
1) Enter the Service Mode. (Press "*" first, and "2" and "8" at the same time,
and then "*.")
2) Select COPIER >FUNCTION > INSTALL> TONER-S.
3) Press the OK key.
- Toner stirring time is approx. 6 minutes. After counting up, it stops
automatically.
- Make the cassette settings before toner stirring is completed. (See Setting
the Cassettes.)
2.2.8 Setting the Cassettes
0007-5065
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / iR3530 /
1) Press the cassette release button, and draw out the cassette to the front.
2) Check the paper series that the user is going to use, and verify whether or
not the paper series selection switch [1] in the cassette matches that of the
user's selection. If not, change the paper size series to the appropriate one.
3) Set the paper size selection dial [2] to the paper size of the paper to be
placed.
[A] [A]
[B]
[B]
[1]
[1]