Chapter 16
16-23
T-16-31
16.4.2 FEEDER
16.4.2.1 FEEDER List
0007-9921
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 /
FEEDER >ADJUST
T-16-32
16.4.3 SORTER
16.4.3.1 Sorter List
0007-9953
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 /
SORTER > ADJUST
T-16-33
COPIER > ADJUST > MISC
Sub-item
Description
Level
IMG-DLY
Entering a fine adjustment value for the image delay in the subscan direction
Make a fine adjustment of the image delay in the subscan direction when image data
is transferred from the controller board to the DCON board.
1
<Setting range>
-128 to 127
iR2270/2270F/2870/2870F: +23 (Default)
iR3570/3570F/4570/4570F: +35 (Default)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
C1/2/3/4-
ADJ-Y
Entering a horizontal registration adjustment value for Cassette 1/2/3/4
Enter the horizontal registration adjustment value for Cassette 1/2/3/4.
Enter the laser writing start position on the paper picked up from Cassette 1/2/3/4,
based on the registered value.
An increase by +1 enlarges the front margin by 0.1mm.
<Note>
When clearing RAM of the DC controller PCB or replacing the PCB, enter the
service label value.
2
<Setting range> -128 to 127 (Default:0)
MF-ADJ-Y
Entering a horizontal registration adjustment value for the multiple manual feed tray
Enter a laser write start position for paper fed from the multiple manual feed tray
according to the registered numeric value.
2
<Setting range>
-128 to 127 (Default: 0)
DK-ADJ-Y
Entering a horizontal registration adjustment value for the side paper deck
Enter a laser write start position for paper fed from the side paper deck according to
the registered numeric value.
2
<Setting range>
-128 to 127 (Default: 0)
FRAME-X
Entering a fine adjustment value in the subscan direction for zooming
Enter an image zooming value in the subscan direction according to the registered
numeric value.
2
<Setting range>
-10 to 10 (-1% to 1%)
FRAME-Y
Entering a fine adjustment value in the main scan direction for zooming
Enter an image zooming value in the main scan direction according to the registered
numeric value.
2
<Setting range>
-10 to 10 (-1% to 1%)
FEEDER >ADJUST
Sub-item
Description
Level
DOCST
Adjusting the front position of document image
<Adjustment method> Setting a greater value delays the image front
timing.
1
<Setting range>
-50 to 50
(Value at shipping: Factory adjustment value / Value after RAM
clearance: 0)
LA-SPEED
Adjusting the document transport speed at feeder flow read
<Adjustment method> Setting a greater value increases the speed
(Reducing the image)
1
<Setting range>
-30 to 30
(Value at shipping: Factory adjustment value / Value after RAM
clearance: 0)
SORTER > ADJUST
Sub-item
Description
Level
PNCH-HLE
Adjusting the distance from the paper end to the punched hole
position
1
<Setting range>
-4 to 2
(Value at shipping / Value after RAM clearance: 0)
Summary of Contents for iR3570 Series
