Canon iR3570 Series, Service Manual

Page: 596 / 722

Chapter 15
15-8
[E602-XXYY]
T-15-4
00 03 Suspension of a write operation to the boot
device has been detected. 1. Find the sector for which the write operation has been
suspended; then, execute recovery operation.
<in the case of black-and-white E code>
1-1 The machine will not permit the use of service mode;
go through the following:
1-2 Turn off the power. Then, turn on the power while
holding down on the 1 and 9 keys so that the repair routine
for the sector for which the write operation was suspended
will automatically start up and the screen will turn solid
black.
1-3 Wait for about 40 to 50 min. There will soon be an
indicator of progress of work. The screen will turn solid
white when the routine ends.
<if the spanner symbol is indicated>
1-1 Set 'CHK-TYPE-0', and execute 'HD-CHECK' (50 to
50 min); thereafter, turn off and then back on the main
power switch.
2. If the symptom still exists after the foregoing, start up in
safe mode; then, format the HDD (full) using the SST, and
re-install the system software (System, Language, RUI),
and turn off and then back on the main power switch.
3. If the symptom still exists after the foregoing, suspect a
fault on the HDD, and replace the HDD and re-install the
system software.
00 04 Symptom absent
00 05 Symptom absent
00 06 The system software of the sub CPU does
not exist. 1. Start up in safe mode, and execute full formatting using
the SST and re-install the system software (System,
Language, RUI); then, turn off and then back on the main
power.
2. If the symptom still exists after the foregoing, suspect a
fault on the HDD, and replace the HDD and re-install the
system software once again.
00 07 The IC profile does not exist. 1. Start up in safe mode, and execute full formatting using
the SST and re-install the system software (System,
Language, RUI); then, turn off and then on the main
power.
2. If the symptom still exits after the foregoing, suspect a
fault on the HDD, and replace the HDD and re-install the
system software.
XX YY
XX CHK-
TYPE
Partition
in
question Description 01 02 03 11, 21 13, 25 10, 12, 14,
22, 23, 24
At startup During routine operation
Reme-dy Reme-dy Reme-dy Reme-dy Reme-dy Reme-dy
1 1 DOSDEV General data
storage area
*1 *5 *9 *10 *11 *12
2 1 FSTDEV Image data
storage area
(e.g., Box) *1 *5 *9 *10 *11 *12
3 1 DOSDEV
2 Image
thumbnail
display data
area (e.g.,
Box) *1 *5 *9 *10 *11 *12
4 1 FSTPDEV Image data
storage area
(e.g., Box)
*1 *5 *9 *10 *11 *12
5 2 DOSDEV
3 General file
storage area
(user settings,
logs, PDL
spool, image
data control
info) *1 *5 *9 *10 *11 *12
6 3 PDLDEV PDL-related
file storage
area (font,
registered
form, ICC
profile, color
correction
info file for
PDL
function)
*1 *5 *9 *10 *11 *12
7 4 DOSDEV
4 Firmware
storage area
(address
book, filter) *2 *6 *9 *10 *11 *12
XX YY Description Remedy