Canon iR3570 Series, Service Manual

Page: 658 / 722

Chapter 16
16-32
FIX-TEMP Switching the plain paper down sequence table
1
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -20 deg C across the board.
2: Set the control temperature at -10 deg C across the board.
3: It is -20Åé only in case of 21Åé or more in room temperature as for the control
temperature.
4: It is -10Åé only in case of 21Åé or more in room temperature as for the control
temperature.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
(For DCON Ver.15 or later)
<Additional information>
This can be set with TEMP-COM or TEMPCON2.
Example)
When FIX-TEMP is set to -6 deg C and TEMP-COM is set to -6 deg C , the control
temperature is offset by -12 deg C .
TRANS-SW Switching transfer high-voltage control from constant current control to constant
voltage control
1
<Setting range>
0: No switching [Default], 1: Constant voltage mode 1, 2: Constant voltage mode 2
TEMP-CON Switching the thick paper fixing temperature mode
1
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -10 deg C across the board.
2: Set the control temperature at -6 deg C across the board.
3: Set the control temperature at -3 deg C across the board.
4: Prioritize fixing performance. Set the control temperature at +3 deg C across the
board.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
<Additional information>
This can be set with FIX-TEMP.
When FIX-TEMP is set to -6 deg C and TEMP-COM is set to -6 deg C, the control
temperature is offset by -12 deg C.
PRIAC-SW Improving the image quality in case of a drum charging fault
Note: This setting is cleared if APVC is executed with a new drum unit or if a
service mode (FUNCTION>D-GAMMA) is executed.
1
<Setting range>
0: No UP [Default], 1: 50 mA UP, 2: 100 mA UP
TEMPCON
2 Improving fixing (Increasing the fixing temperature)
Switching the multiple plain paper fixing temperature mode
<Note>
This is only valid for iR3530/3570/3570F/4530/4570/4570F.
1
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -10 deg C across the board.
2: Set the control temperature at -6 deg C across the board.
3: Set the control temperature at -3 deg C across the board.
4: Prioritize fixing performance. Set the control temperature at +3 deg C across the
board.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
<Additional information>
This can be set with FIX-TEMP.
When FIX-TEMP is set to -6 deg C and TEMPCOM2 is set to -6 deg C, the control
temperature is offset by -12 deg C.
CONFIG Selecting several types of firmware installed on the hard disk and switching the
country, language, and paper size type of this machine
1
<Adjustment method>
XXYYZZAAXX: Country (UP), YY: Language (ja), ZZ(00) Destination, AA(00):
Paper size type
The display contents conform to the display method of
(COPIER>DISPLAY>USER>LANGUAGE). Enclosed in the brackets are
defaults. The country and language are only displayed.
<Operating procedure>
1) Select <CONFIG>.
2) Select an item to reverse its display. Then press the + or - key to change the
contents.
3) Each time the + or - key is pressed, the contents change sequentially.
4) Display the intended contents at all items and press the OK key.
5) Turn the main power switch OFF and ON.
W/SCNR Setting whether a scanner is present (Copy model) 1
<Setting range>
0: Printer model [Default]
1: Model with scanner
COPIER > OPTION > BODY
Sub-item Description Level