Canon iR3570 Series, Service Manual

Page: 615 / 722

Chapter 15
15-27
E540 0002
Upper tray ascent/
descent motor error
(Finisher -Q3/Q4)
Upper tray ascent/
descent motor clock
error
Replace the No. 1 tray shift motor.
Replace the finisher controller
PCB. Check the tray ascent/descent
mechanism.
0003
Area error
Replace the No. 1 tray area sensor
PCB. Replace the finisher
controller PCB.
0004
Safety switch activation
Check the No. 1 tray closed
detecting switch. Replace the
finisher controller PCB.
E542 0002
Lower tray ascent/
descent motor error
(Finisher-Q3/Q4)
Lower tray ascent/
descent motor clock
error
Replace the No. 2 tray shift motor.
Replace the finisher controller
PCB. Check the tray ascent/descent
mechanism.
0003
Area error
Replace the No. 2 tray shift area
sensor PCB. Replace the finisher
controller PCB.
E577 8001
Paddle error (Finisher-
S1)
The paddle home
position sensor does not
go on within 1.5 sec
when the paddle is
shifted to home
position. Check the paddle motor. Check the
paddle home position sensor.
Replace the finisher controller
PCB.
8002 The paddle home
position sensor does not
go off within 1.0 sec
when the paddle is
moved to home
position.
E584 0001
Shutter unit error
(Finisher-Q3/Q4)
The shutter open sensor
does not go off (i.e., the
shutter does not close). Check the stack edging motor.
Check the open/close clutch. Check
the shutter home position sensor.
Replace the finisher controller
PCB.
0002 The shutter open sensor
does not go on (i.e., the
shutter does not open).
E590 0001
Punch motor error
The punching home
position is not detected
even when the puncher
motor has been driven
for 20 msec. Check the punch motor. Check the
punch motor clock sensor. Check
the punch driver PCB. Replace the
finisher controller PCB.
0002 The punch home
position sensor is not
defected even after the
motor has stopped at
time of punch motor
initial operation.
E591 0001
Punch dust sensor error
Error in light-receiving
voltage while light is
emitted Check the waste paper case full
sensor. Check the punch driver
PCB. Replace the finisher
controller PCB.
0002 Error in light-receiving
voltage while light is
not emitted
E592 0001 Paper trailing edge
sensor/horizontal
sensor error
Error in light-receiving
voltage when light is
emitted (trailing edge
sensor)
Check the paper trailing edge
sensor. Check the horizontal
registration sensor. Check the
punch driver PCB. Replace the
finisher controller PCB.
E592 0002 paper trailing edge
sensor/registration
sensor error
Error in light-receiving
voltage when light is
not emitted (trailing
edge sensor)
Check the paper trailing edge
sensor. Check the horizontal
registration sensor. Check the
punch drive PCB. Replace the
finisher controller PCB.
E592 0003 Power trailing edge
sensor/registration
sensor
Error in light-receiving
voltage when light is
emitted (horizontal
registration sensor 1)
Check the paper trailing edge
sensor. Check the horizontal
registration sensor. Check the
punch driver PCB. Replace the
finisher controller PCB.
E592 0004 Paper trailing edge
sensor/registration
sensor error
Error in light-receiving
voltage when light is
not emitted (horizontal
registration sensor 1)
Check the paper trailing edge
sensor. Check the horizontal
registration sensor. Check the
punch driver PCB. Replace the
finisher controller PCB.
E592 0005 Paper trailing edge
sensor/registration
sensor error
Error in light-receiving
voltage when light is
emitted (horizontal
registration sensor 2)
Check the paper training edge
sensor. Check the horizontal
registration sensor. Check the
punch driver PCB. Replace the
finisher controller PCB.
E592 0006 Paper trailing edge
sensor/registration
sensor error
Error in light-receiving
voltage when light is
not emitted (horizontal
registration sensor 2)
Check the paper training edge
sensor. Check the horizontal
registration sensor. Check the
punch driver PCB. Replace the
finisher controller.
Code Detail code Name Detection Remedy