Canon iR3570 Series, Service Manual

Page: 590 / 722

Chapter 15
15-2
15.2 Error Code Details
15.2.1 Error Code Details
0008-1078
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / /
T-15-2
E716
communication error for pedestal/ communication error for 3-way unit-
A1
E717 communication error for NE controller
E719 coin vendor error
E730 PDL software error
E732 scanner communication error
E733 printer communication error
E740 Ether board error
E743 DDI communication error
E744 language file/boot ROM error
E745 TokenRing board error
E746 accessories board wrong model error
E748 controller board and SDRAM size mismatch
E805 fan error
Code Cause Remedy
E000 The temperature of the fixing assembly is abnormally high.
0001 While startup control is under way, the reading of
the main thermistor is less than 30 deg C
continuously for 200 msec or more 1 sec after the
start of power supply.
While startup control is under way, the reading of
the main thermistor is less than 70 deg C
continuously for 200 msec or more 2 sec after the
start of power supply.
While startup control is under way, the reading of
the main thermistor is less than 120 deg C
continuously for 200 msec 6 sec after the start of
power supply.
The startup control does not end 30 sec after the
start of power supply.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
E001 The temperature of the fixing assembly is abnormally high.
0000 The reading of the main thermistor is 250 deg C
or more continuously for 200 msec.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
0001 The hardware circuit detects overheating of the
main or sub thermistor for 200 msec.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
DC controller PCB.
0002 The reading of the sub thermistor is 295 deg C or
more continuously for 200 msec.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
sub thermistor. Replace the DC controller PCB.
E002 The rise in temperature of the fixing assembly is faulty.
0000 While startup control is under way, the reading of
the main thermistor is less than 115 deg C
continuously for 400 msec 1.3 sec after it has
indicated 100 deg C.
While startup control is under way, the reading of
the main thermistor is less than 150 deg C
continuously for 400 msec 1.3 sec after it has
indicated 140 deg C.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
E003 The fixing temperature is too low after a standby state.
0000 While regular temperature control is under way,
the reading of the main thermistor is less than 140
deg C continuously for 400 msec or more.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
E007 The rotation of the fixing film is faulty.
0000 While the fixing motor is rotating, the marker
signal is not detected for 6 sec with the reading of
the main thermistor indicating 100 deg C or more.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
E010 The rotation of the main motor is faulty.
0001 Detection is executed every 100 msec after the
start of motor rotation; however, the drive
detection signal is absent for 2 sec.
Replace the main motor. Replace the DC controller
PCB.
0002 During motor rotation, detection is executed
every 100 msec; however, the drive signal is
absent 5 times in sequence.
Replace the main motor. Replace the DC controller
PCB.
E014 The rotation of the fixing motor is faulty.
0001 Detection is executed every 100 msec after the
start of motor rotation; however, the drive
detection signal is absent for 2 sec.
Replace the fixing motor. Replace the DC controller
PCB.
Code Error name/description