Canon iR3570 Series, Service Manual

Page: 565 / 722

Chapter 14
14-37
first copy output time (FCOT) of the machine.
- iR4570 series: Ambient temperature is 17 deg. C or lower (Initial rotation time: 7 seconds longer than usual)
- iR2270 series: Ambient temperature is 13 deg. C or lower (Initial rotation time: 5 seconds longer than usual)
14.2.10.1.54 How to check extended printer options: Device Configuration
0010-4194
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Manual-related ]
Field Remedy
Follow the procedure below to check the extended printer options.
1. Press the counter check key on the control panel, and then press "Device Configuration" to check if a printer option is displayed on any of the software
option fields. Note that the Printer Expansion Kit-A1 can be checked in this field, however, the UFR II Printer Kit-E3 cannot be checked. If no option is
displayed in the field, go to the step2.
2. In service mode [COPIER > ACC-STS > PDL-FNC1], check the value of each bit displayed. Starting from the left, each bit shows the following in
sequence: BDL, PS. PCL, PDF, LIPS, N201, I5577, ESC/P, HPGL, HPGL2, IMAGING, and KS. (The remaining bits are reserved.) If a printer option has
been extended, the corresponding bit is set to "1".
14.2.10.1.55 Are all destinations in Address Book deleted when RAM on Main controller PCB is cleared?
0010-4202
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Manual-related ]
Description
All destinations registered in the address book and all service data are deleted when the data of RAM on the DC controller PCB is cleared in the service mode.
When clearing the RAM data, follow the procedure below in advance to keep all the destinations in the address book and all service data.
a. Backup of all destinations in Address Book to a PC
In the Remote UI screen [Add. Func. > Import/Export > Address Book > Export > Start Export].
b. Backup of all service data
In service mode [COPIER > FUNCTION < MISC-P > P-PRINT], output all the service mode values as a P-Print.
14.2.10.1.56 How many sheets of paper can be loaded on Buffer Pass Unit-E1?
0010-4378
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Manual-related ]
Description
The number of sheets that can be loaded on the buffer pass unit-E1 is as follows:
- A4/A5R/LTR/STMTR size paper: 100 sheets at a maximum
- A3/A4R/LDR/LGL/LTRR size paper: 50 sheets at a maximum
14.2.10.1.57 Horizontal registration adjustment is not as required even after adjusting cassette position: 2-Cassette Pedestal-Y2
0010-4379
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Case in the field ]
Description
At time of installation, horizontal registration adjustment is performed by executing the cassette position adjustment and the service mode adjustment.
Therefore, when horizontal registration adjustment is not as required under the set of standards even after executing the cassette position adjustment, follow
the procedure below to enter the horizontal registration adjustment value in service mode.
Field Remedy
In serviced mode (Level2) [COPIER > ADJUST > MISC > C3-ADJ-Y (for cassette 3)/C4-ADJ-Y (for cassette 4) > enter a value > OK]. This will change
the laser write start position for paper fed from a cassette. An increase of '1' will increase the front margin by 0.1mm. (Adjustment range: -128 to 127, the
value at time of factory shipment:0)
14.2.10.1.58 DADF-N1: Adjustments to be required when installing DADF-N1
0010-4380
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Case in the field ]
Description
The following adjustments are required when installing DADF-N1.
Field Remedy
When installing the DADF-N1, make the following eight adjustments referring to the installation manual that comes with the unit.
1. Height adjustment
2. Tray width adjustment
3. Right angle adjustment
4. Read position adjustment
5. Magnification adjustment
6. Horizontal registration adjustment
7. Trailing edge registration adjustment
8. White level adjustment
14.2.10.1.59 DADF-N1: Scanning operation in different size originals mode
0010-4382
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Case in the field ]
Description
When selecting the different size originals mode as a special feature of a copying job and scanning either of the following combination of original size from
the DADF-N1; LTR and LDR, LTRR and LGL, STMT and LTRR, or LGL and STMT, if "Same Width" is selected in the copy screen [Special Features >
Different Size Originals], the machine feeds the originals as if it scans two-sided originals. However, if "Different Width" is selected under Special Features,
the machine never operates in such a manner.
14.2.10.1.60 Condensation upon installation/faulty image/malfunction
0010-4383
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /