manualshive.com logo in svg

Artesyn MVME5100, Programmer'S Reference Manual, Page: 170 / 318

Share
Download
Artesyn MVME5100 Programmer'S Reference Manual Download Page 170

Hawk PCI Host Bridge & Multi-Processor Interrupt Controller

MVME5100 Single Board Computer Programmer’s Reference (6806800H17B

)

170

NIRQ

NUMBER OF IRQs. The number of the highest externalIRQ source supported. The IPI, Timer, 
and PHB Detected Error interrupts are excluded from this count.

NCPU

NUMBER OF CPUs. The number of the highest physical CPU supported. There are two CPUs 
supported by this design. CPU #0 and CPU #1.

VID

VERSION ID. Version ID for this interrupt controller. This value reports what level of the 
specification is supported by this implementation. Version level of 02 is used for the initial 
release of the MPIC specification.

2.5.3.3

Global Configuration Register

RESET

NIRQ

NCPU

VID

Operation

R

R

R

R

R

Reset

$0

$00F

$0

$01

$03

Table 2-71 Feature Reporting Register (continued)

Offset

$01000

Bit

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Table 2-72 Global Configuration Register 

Offset

$01020

Bit

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Name

GLOBAL CONFIGURATION

RE

SE

T

EINT

T

M TIE

Operation

C R R/W R/W

R

R

R

R

Reset

0 0 0 0

$00

$00

$00

$00

Summary of Contents for MVME5100































































































































































































































































































































Reviews:

No comments